Jameco Electronics 527822 User Manual

The content and copyrights of the attached material are the property of its owner.Distributed by:www.Jameco.com ✦ 1-800-831-4242Jameco Part Number 52

A8. Click “Next” to continue (Ref Figure A-5) Figure A-8 A9. Click “Next” to continue (Ref Figure A-5) Figure A-9 A10. Click “Finish”,

Step B: Printer Adapter Installation (This section for Windows98/98SE/Me) To install the software for USB to Printer Converter of the USB 2.0 DOCK:

B4. Click “Next” to continue (Ref Figure B-4) Figure B-4 B5. Click “Finish”. Windows has finished installing the prin

Step C. USB Composite Device for PS/2 keyboard & mouse Installation (This section for Windows98/98SE only) C1. Click “Next” to continue (Ref F

C4. Click “Next” to continue (Ref Figure C-4) Figure C-4 C5. Click “Finish”. Windows has finished installing the USB Composite device driver for PS

Step D: Serial Converter Installation (Required for 98/98SE/Me Windows System) To install the USB to serial port driver of the USB 2.0 DOCK, please

D4. Click “Next” to continue (Ref Figure D-4) Figure D-4 D5. Click “Finish”. Windows has finished installing RS-232 Serial port driver (Ref Figure

Step E. USB HID Device for PS/2 keyboard & mouse Installation (This section for Windows98/98SE only) To install the USB HID device PS/2 key

E4. Click “Next” to continue (Ref Figure E-4) Figure E-4 E5. A warning message window will show up. Please insert the Windows 98 CD and Click “OK”

Win2000 Driver Installation To install the driver of the USB 2.0 DOCK, please make sure the driver CD is inserted. Step1. Click “Next” to contin

User’s Manual USB 2.0 DOCK

Step4. Click “Next” to continue (Ref Figure Win2k -4) Figure Win2k -4 Step5. Click “Finish”, Windows has finished installing Serial port driver.

WinXP Driver Installation To install the USB to serial port driver of the USB 2.0 DOCK, please make sure the driver diskette/CD is inserted: Ste

Congratulations!! You have finished installing USB 2.0 DOCK. Please click on Start>> Settings>> Control Panel, and double click System, a

Set Up the Printer Device Follow the steps below to connect your printer to the USB 2.0 DOCK with your PC: For Windows 98/98SE and Me: 1. Turn off

Figure 6 6. If you do not have a printer installed yet, click on Start, Settings, Printers, Add Printer. The Add Printer Wizard will start and assi

For WINDOWS 2000 and XP: 1. Turn off your printer. Plug in the cable to connect USB 2.0 DOCK parallel port and printer. Turn on the printer afterwar

Set up the HyperTerminal with USB to serial port Follow the steps below to configure your HyperTerminal with USB to serial COM port setting: 1. Make

Figure 9 4. Click the "Connect using" item to indicate the proper COM port which appeared in step 1, and follow the succeeding instructio

Uninstalling the Driver Program If you want to remove the USB 2.0 DOCK driver program, you can uninstall it by following the steps below: a. Unplug

d. For WIN2000/XP: Please Press OK to remove Serial Convertor. System will require to restart to complete the un-installation. Please press Ye

Index INTRODUCTION ...3

APPLICATION NOTE 1. USB 2.0 DOCK normally derives its own power from PC Host. When system power plugged in to the USB port of PC or notebook, the La

USB 2.0 DOCK User’s Manual - 30 - Disclaimer Information in this document is subject to change without notice. The manufacturer does not make any rep

Introduction Thank you for ordering the USB 2.0 DOCK. The USB 2.0 DOCK is an intelligent expansion module, which connects to a PC or notebook via U

Connectors  One DB-9 RS-232 serial interface connector supports baud rates from 1,200 to 115.2K.  One DB-25 parallel connector supports IEEE-1284 bi

LED Indicator  Power Indicator The Power Indicator will turn ON when bus power is supplied.  USB Indicators There are four USB indicators to show i

Installing USB 2.0 DOCK 1. This installation guide is written in accordance with different operation systems. Including Windows 98/98SE/Me, Windows

Win98/98SE/Me Driver Installation The driver installation is divided into 5 steps. For Win98/98SE installation should include all 5 steps (A-E).

A4. Click “Next” to continue (Ref Figure A-4) Figure A-4 A5. Click “Finish”, Windows has finished installing USB 2.0